drawing & mounting du cone driver BMS BMS 8N (8Ohm) spl vs frequency measurement du cone driver BMS BMS 8N (8Ohm) spl vs impedance. 96 dB Sensitivity 1 W / 1 m W Power Handling Extremely light Weight of kg 2″ Aluminium Sandwich Voice Coil for low Power Compression Double. Ciare FXI MR 8Ω. ” Mid-range. Fs, Hz. Power RMS, W, Qts, Sensitivity, 97 dB, Vas, litres. Freq-range, 90 – Hz, Xmax, mm.
|Published (Last):||28 September 2008|
|PDF File Size:||9.47 Mb|
|ePub File Size:||8.1 Mb|
|Price:||Free* [*Free Regsitration Required]|
To that end I suggested he used a particular Bass driver which I then could see he had already considered. Do neodymium magnets not in general have smaller voicecoil gaps and therefore lower distortion factors, than with a larger more resonant gap?
Plansound – Licht- Ton- Bühnen- und Veranstaltungstechnik – Vermietung und Verkauf
I’ve been looking at a pair of 8″ drivers to sit below the BMS Nd For the purpose of this question i’l restrict the drivers layed out to: I know what 2 x the above mentions 8″ jobbies mentioned will do and a pair of them will work very well with the bass drivers to allow a hz ish X-over to the bass.
OP use the 8S With all this in mind, disregarding prices which obviously makes the 8S desirable is the slightly higher moving mass and the slightly lower sens in the 8N that unwanted, as to make the 8N better despite the immediate visual inferiority?
Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum.
If anyone could possibly help me, id much appreciate it: You need to be using something bigger I’d reckon 12 or 15 before its paying its way. Its a part of a larger 4-way application in which so far theoreticly the low end is handled by 4×12″ If you go back to the original thread you will see that the OP wanted Hi-Fi sound. Don’t test the champignon sound.
BMS 8″ Driver
I agree that the is capable of more but look at the loads of folks that use them for home hi-fi, hundreds in the States: The question was put mainly to get a grasp on what the topic states too, the reasoning for choosing drivers compared to the data presented without having actually heard it Maybe i should have added that this does not present the whole system I did notice the differences in distortion’s however is that what might wheigh heavy on the 8h515 D just two thoughts: Thank you for your input tho.
O That is because they are often used solely with a 15″ bass driver. Most linear FR, Lower Fs, Higher Xmax, More power handling Do neodymium magnets not in general have smaller voicecoil gaps and therefore lower distortion factors, than with a 8515 more resonant gap? None the less, il give it a go. From what i can see and with my limited capability interpret by the data, my reasoning would tell me that the 8N has all the pro’s and no con’s going for it.
BMS 8N – 8″ Neodymium Bass Midrange Speaker W 8 Ohms from BMS £
Hey yall, dunno if im placing this in the wrong section as im fairly “unadvanced”: I would then cross the around hz. Edited by CMS – 25 November at And how about getting all 3 and testing them, bmss keep the one you like most?
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum.
This page was generated in 0.