Catálogo SP. Aplicaciones para ruedas de camiones y transporte pesado: Incluye especificaciones y intercambios. Rodamientos y. Sellos SKF. From one simple but inspired solution to a misalignment problem in a textile mill in. Sweden, and fifteen employees in , SKF has grown to become a global. Heavy Duty Pillow Block Maintenance Handbook Catalogue No. CDN SKF Canada Limited AN ISO REGISTERED COMPANY Proud recipient of The.

Author: JoJoll Kazibar
Country: Bosnia & Herzegovina
Language: English (Spanish)
Genre: Technology
Published (Last): 12 March 2008
Pages: 465
PDF File Size: 9.69 Mb
ePub File Size: 3.61 Mb
ISBN: 838-8-89054-631-7
Downloads: 38455
Price: Free* [*Free Regsitration Required]
Uploader: Akizilkree

For extreme operating conditions D and E type labyrinth seals are standard. The bearing is mounted on the shaft directly or chumacerad an adapter sleeve and filled with grease. Extremely user-friendly due to spring operated and self-locking arms, gripping b ehind the component with just one movement of the hand Ergonomic red-rings Available in three sizes with a maximum withdrawal force of 3, 5 or 8 tonnes 30, 50 or 80kNenabling easy selection Hydraulic force generators available for the 8 tonne 80kN EasyPull Light-weight Safe: With bearing hand tight on the adapter, relocate if necessary, the bearing and the adapter to the proper axial location on the shaft.

SDAF pillow blocks can also be supplied in cast steel.

Rodamientos, Sellos, Lubricación, Mecatrónica y Servicios | Grupo SKF

Finally the silicon O-ring is placed in the grooves of the labyrinth seals. When heated by an SKF induction heater, catalovo bearing becomes the short circuited, single turn secondary coil through which a high current catalogl ws at a low voltage, generating heat. Adapter Sleeve Mounting Spherical RollerFor a large size adapter sleeves size 44 and up the use Bearings of the oil injection mounting method is standard practice.

The choice of lubricants depends primarily on the temperature range, operating speed and magnitude of the load. The recommended intial grease charge is one-third to one-half the volume of the free space in th e pillow block, and the empty space between rolling elements and cage chumacerxs with grease buttered.

The locknut will be damaged and chips can enter the bearing. As a precaution, never mix greases with unlike base oils or incompatible thickeners. If slot is past tab, do not loosen nut, but tighten until a tab can be bent into a slot. For xkf LORC seal insert the inboard LOR seal with the added sealing component assuring that the rubber sealing component is facing in the correct orientation to make it either purgeable or non-purgeable. Head bolts, e xcept which uses 4 bolts.



No need to buy expensive spare-parts; a cuumaceras safety pin breaks should excessive force be used Service life of puller extended by safety pin Self-centering avoids damage to shaft Efficient use of time due to quick dismounting For additional Maintenance Products Tooling, Heaters and Lubricants contact you local SKF sales office or www. At low and medium speeds, grease usually permits a simpler method of obtaining reliable and durable lubrication.

Xkf attaching the measuring units to the shafts the on-screen instructions guide you simply through the alignment prcedure. The second labyrinth seal cumaceras placed on the shaft following instruction as described above under 2 except reverse sequence. The bearing is mounted on the shaft directly or on an adapter and filled with grease. Also if shimming is required, only shims giving full mounting support must be used.

Remove locknut and mount lockwasher with inner prong located in the slot provided in the adapter and the tabs on washer O. Contaminated grease results in xhumaceras such as premature fatigue, polishing wea r, etc. To recognize A-design, cap of Series: With high speeds, it becomes necessary to add fresh grease and remove old grease more frequently to obtain safe operation. At the first charge of grease, the bearing MUST be filled with grease.

The shaft, complete with bearing assembly and labyrinth seals, is placed in the lower half of the housing. The mounting bolts are tightened to the support. The housing base is placed in position and the mounting bolts loosely fitted. Post on Oct views.

The relubrication intervals hours of operation obtained from Diagram A are valid for bearings in stationar y machines where loading conditions are normal. Apply the locknut with the chamfered face toward the bearing after lubricating the face of the locknut next to the bearing.


This reduc tion also applies to applications where the grease is required to seal against moisture e. At the initial start up, with shaft rotating, lubricate seals through grease fitting until a bead of grease appears around the periphery of the flingers. It s as easy as that. The housing cap is fitted and the cap bolts tightened to the recommended torque, see table on Pages 26 through And at a very competitive price!

In the majority of cases it is sufficient to charge the housings with grease on mounting and to replace this grease periodically, either at specified time interval or when performing inspections.

EasyPull dismounts the most difficult bearings Dismounting a bearing can be a demanding task for both user and puller. To insure that the nut is not excessively tight, make certain the outer ring of the bearing rotates freely.

With that fundamental engineering principle in mind, SKF, the world s largest bearing manufacturer, has introduced S KF SYSTEM 24, a new generation of automatic lubricators that bridge the conflicting interests of commercial need a nd environmental pressures. Variety of sealing arrangements available, see Page 8.

Lubrication through center fitting for W33 Non W33 If grease is used as a lubricant, at installation of bearing the chumacersa must be worked in between the rolling elements. Supplied in ductile iron as standard and stronger than the old designs. Use same grease as for lubrication of bearing.

The maximum permissible misalignment of the shaft is approximately 1. Note that the cap must not be interchanged with that of another housing.