CE1 IEC (Première édition – ) (First edition – ) Courants de court-circuit dans les réseaux Short-circuit currents in three-phase. IEC Edition INTERNATIONAL. STANDARD. NORME. INTERNATIONALE. Short-circuit currents in three-phase a.c. systems –. Buy IEC SHORT-CIRCUIT CURRENTS IN THREE-PHASE A.C. SYSTEMS – PART 0: CALCULATION OF CURRENTS from SAI Global.

Author: Kasho Gujin
Country: Pakistan
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 7 July 2004
Pages: 375
PDF File Size: 1.71 Mb
ePub File Size: 18.15 Mb
ISBN: 938-2-65625-446-9
Downloads: 93250
Price: Free* [*Free Regsitration Required]
Uploader: Kigalabar

Electric and magnetic devices IEC The initial short-circuit current at the short-circuit location F is the phasor sum of the individual partial short-circuit currents see figure They do not ieec to the symmetrical short-circuit breaking current I, and the steady-state short-circuit current I k. Special considerations are necessary in this case, for instance with the superposition method.

This is possible if the d. Nominal system voltage, line-to-line r.

Short Circuits in Power Systems: A Practical Guide to IEC 60909-0, 2nd Edition

Within the accuracy of this standard, it is often sufficient to determine the isc current at the short-circuit location F as being the sum of the absolute values of isc individual partial short- circuit currents. Factors ;Iminand il,,for salient-pole generators Example of a meshed network fed from several sources For this calculation method, an equivalent voltage source at the short-circuit location is introduced. Normally, the steady-state short-circuit current Ik is smaller than the symmetrical short-circuit breaking current 1.

Calculation of a Generator 8. The generator impedance shall be transferred to the high-voltage side using the rated transformation ratio t. The factor p may also be obtained from figure In the case of high-voltage direct-current transmission systems, the capacitor banks and filters need special considerations, when calculating a.

The deviation depends on the configuration of the network. For the purpose of this standard, one has to make a distinction between short-circuit impedances at the short-circuit location F and the short-circuit impedances of individual electrical equipment.

  JAMES OSCHMAN ENERGY MEDICINE PDF

The effective resistance of the stator of synchronous machines lies generally much below the given values for RGf. Xk may be neglected.

The superposition method gives 600909-0 short-circuit current related to the one load flow presupposed. You are currently using lec site but have requested a page in the site. Zero-sequence impedance arrangements for the calculation of unbalanced short-circuit currents are given in IEC The effect of series capacitors can be neglected in the calculation of short-circuit currents, if they are equipped with voltage-limiting devices in parallel, acting if jec short circuit occurs.

CE1 TR–I read: Low-voltage motors are to be taken into account in auxiliaries of power stations uec in industrial and similar installations, for example in networks of chemical and steel industries and pump- stations. Factor q may also be obtained from figure For simplification, it is permitted to use the same value of Kas for the three-phase short circuit.

At this date, the publication will be 0 reconfirmed; 0 withdrawn; 0 replaced by a revised edition, or 0 amended. The factor K shali be calculated according to 4. These values cannot be used when calculating the aperiodic component id.

Log In Sign Up. Their preparation is entrusted to technical committees; any IEC 6090-90 Committee interested in the subject dealt with may participate in this preparatory work. Methods of Calculations 1 1.

For the calculation of the initial short-circuit currents according to 4. For the short-circuit impedance of synchronous generators in the zero-sequence system, the following applies with KG from equation 1 8: This part ief IEC establishes a general, practicable and concise procedure leading to results, which are generally of acceptable accuracy.

The positive-sequence short-circuit impedance zat the short ic location F is obtained according to figure 5a, when a symmetrical system of voltages of positive-sequence phase order is applied to the short-circuit location F, and all synchronous and asynchronous machines are replaced by their internal impedances.

  CENTURYLINK WESTELL 7500 MANUAL PDF

The impedance correction factor shall be applied also to the negative-sequence and the zero- sequence impedance of the transformer when calculating unbalanced short-circuit currents.

For the examples in figures 1Ib and 1 IC, the initial symmetrical short-circuit current is calculated with the corrected impedances of the generator and the power station unit see 3.

Short Circuits in Power Systems: Calculation of Short-Circuit Currents Read an Excerpt Excerpt 1: Medium-voltage motors have to be considered in the calculation of maximum short-circuit current see 2.

Radial Network Q5 This standard meets my needs: The impedance ZrS1in equation 38 or 43 is used to determine the partial short-circuit current ILT in figure 13 for the short circuit in F3. Calculation of a Oec 8.

IEC | IEC Webstore

In the case of high-voltage feeders with nominal voltages above 35 kV fed by overhead lines, the equivalent impedance 2, may in many cases be considered as a reactance, i. Would you like 6099-0 change to the site? Equations 84 and 85 are valid in the case of far-from-generator and in the case of near-to- generator short circuits. When a number of short circuits occur with a short time interval in between them, the resulting Joule integral is the sum of the Joule integrals of the individual short-circuit currents, as given in equation 1 T JSrT ; t, is the rated transformation ratio of the unit transformer: